Details
The LYNK+ Core Radiator Module 360 is a factory-filled radiator and pump module for the modular LYNK+ liquid cooling system. Its aluminum radiator has a slim 30mm profile and room for three 120mm fans, and the integrated pump circulates the coolant with low operating noise. Drip-free Quick Connect fittings join it to a LYNK+ cooler module such as the RTX 5090 Upgrade Kit Cooler, which fits the graphics card with its matching plate kit (Plate Kit Reference Design or Plate Kit Zotac).
Properties
- Size
- 360mm, 3x 120mm fans
- Dimensions
- 409 x 120 x 30mm
- Material
- Aluminum, black frame and fins
- Pump
- Integrated, 3,900 to 4,700 RPM, ceramic bearing
- Tube length
- 450mm
- Fans
- Not included
- Coolant connection
- LYNK+ drip-free Quick Connect
- Pump power
- SATA
Slim Core design
The Core design removes the extended LED bottom tank of earlier LYNK+ radiator models to improve case compatibility, while keeping the integrated pump and the modular LYNK+ connection system. The 360mm format gives more radiator surface than the 240mm model; choose it when your case has room for the bigger cooling setup.
Case and fan compatibility
Your case must support 360mm radiators: not every case that takes three 120mm fans in a row also takes a radiator, and radiators differ in length. This radiator is 409mm long and LYNK+ advises allowing 410mm, so check the clearance, or look your case up in LYNK+'s PC case compatibility list.
The radiator works with standard wired 120mm fans, and screws for 25mm and 30mm thick fans are in the box. LYNK+ notes that some daisy-chain fan models can have compatibility issues, so check their outer dimensions. Pair the radiator with high static pressure fans to push air through its high-density fin structure, and adjust the fan curve to suit the fans you install.
Integrated pump, your choice of fans
The pump sits under the cover at one of the tube connections and uses a decoupled mounting design that LYNK+ says reduces vibration and operating noise. LYNK+ validated the pump for over 50,000 hours under load. The fans are your choice, so you can pick the balance of acoustics, performance and appearance you want.
Modular AIO liquid cooling
LYNK+ is a modular all-in-one liquid cooling system for graphics cards. Pre-filled GPU cooler and radiator modules combine into one liquid cooling system without the work of building, filling and maintaining a traditional custom loop. The radiator module can be kept when you change graphics cards: only the cooler module and its plate kit are swapped for the new card.
Drip-free Quick Connect
The modules join with one screw. LYNK+ says its patented, self-sealing Quick Connect lets modules be connected without draining or refilling the system, and it stays watertight through the whole coupling process. Electrical contacts in the Quick Connect carry the pump and fan PWM and RPM signals along wires that run beside the tubing, so no cable runs between the radiator and the graphics card.
Factory-filled and ready to install
Every module arrives filled and sealed. No coolant bottle, filling equipment, bleeding process or initial leak test is needed: mount, connect and complete the standard PC connections. LYNK+ designed the system for more than five years of operation without routine draining, refilling or coolant maintenance, using a sealed architecture with low-diffusion tubing, integrated air storage and pressure-tested connections.
Connections
Connect the three fans as a daisy chain with Y splitter cables, and the first one to the 4-pin PWM connector on the front of the radiator between the tubes: the radiator module powers the fans and passes their RPM signal on. The pump takes SATA power from the power supply. Fan and pump speed are controlled through the 4-pin fan cable of the LYNK+ GPU cooler on your motherboard. A status LED on the front of the radiator module shows normal operation, bus or pump errors and missing power; the manual lists the blink codes.
Technical data
| Type | Factory-filled modular liquid cooling radiator with integrated pump |
| Radiator size | 360mm |
| Dimensions (L x W x H) | 409 x 120 x 30mm |
| Radiator thickness | 30mm |
| Material | Aluminum |
| Color | Black frame and fins |
| Weight | 1,500g |
| Tube length | 450mm |
| Factory filled | Yes |
| System compatibility | LYNK+ cooler modules |
| Fan support | 3x 120mm |
| Included fans | 0 |
| Fan mounting screws | For 25mm and 30mm thick fans |
| Pump speed | 3,900 to 4,700 RPM |
| Pump bearing | Ceramic |
| Maximum pump noise | 21.75 dB(A) |
| Display | None |
| Coolant connections | LYNK+ drip-free Quick Connect |
| Pump power | SATA |
| Product series | LYNK+ RTX 50 Series |
Notes
- Screw the Quick Connect in with the hex key until you feel a hard stop and it sits flush with the cooler front. It stays watertight all the way through, so there is no need to tighten further after it stops.
- If the pump reports an error after startup, LYNK+ says a restart usually clears it; if it persists, gently tilt the radiator during startup so trapped air can move into the reservoir.
In the box
- 1x 360mm Radiator module
- 1x Quick Connect screw
- 1x LYNK+ hex key
- 1x User manual QR
- 12x Case screws
- 12x Fan screws for 25mm thick fans
- 12x Fan screws for 30mm thick fans
LYNK+'s user manual for the RTX 5090 Upgrade Kit (cooler, plate kit and radiator), its GPU and Plate Kit compatibility list and its PC case compatibility list are PDFs.
