Welcome!

Shopping cart
0

Arctic Silver ArctiClean 60ml Two Part Kit (ACN-60ml)

Availability: In stock - Available Now

Sku: ACN-60ml

$11.25

Quick Overview

Arctic Silver ArctiClean two-step kit: ArctiClean 1 dissolves old thermal paste and pads, ArctiClean 2 purifies the surface for new thermal material. 2x 30 ml.

Details

ArctiClean is a two-step cleaning kit from Arctic Silver, the first retail product from the union of Arctic Silver and Nanotherm technology. Step 1 dissolves old thermal grease or thermal pads from the CPU and heatsink, step 2 removes the residue and prepares the surface for a fresh application of thermal interface material. The kit holds 30 ml of each.

Properties

Type
Thermal material remover and surface purifier
Steps
2 (ArctiClean 1 and ArctiClean 2)
Contents
2x 30 ml bottles (60 ml)
For
Copper and aluminum heatsinks, CPU heat spreaders

Step 1: Thermal Material Remover

ArctiClean 1 uses a proprietary combination of citrus and soy based solvents to emulsify and dissolve thermal grease and thermal pads, so the old material wipes off with a clean cloth or paper towel. Arctic Silver describes the solvents as non-toxic and biodegradable and says they match or exceed many hazardous and volatile solvents such as fluorinated and chlorinated solvents, acetone, MEK, mineral spirits, isopropyl alcohol and toluene.

Step 2: Thermal Surface Purifier

The cationic surfactants in ArctiClean 2 remove the residue left by ArctiClean 1 and leave a clean surface for the new thermal interface material. Flash corrosion inhibitors minimize the corrosion layer on copper and aluminum, for closer contact between the thermal material and the heatsink. ArctiClean 2 also removes the residue of other citrus or petroleum based cleaners.

Why not just alcohol or acetone?

Arctic Silver explains that isopropyl alcohol or acetone may soften a thermal pad but does not dissolve it, so it takes a lot of rubbing and scrubbing; the same is true, less visibly, for thermal grease. ArctiClean 1 emulsifies the waxes, oils and fillers of the thermal material and keeps them suspended, so they also come out of the microscopic imperfections in the heatsink or heat spreader.

How to use it

  • Remove rings or other jewelry that could scratch the surfaces. Take the heatsink or water block off and lay both parts on a clean, flat surface, thermal surfaces up.
  • Pads: scrape off most of the pad with a credit card or similar plastic piece without scratching the base. Compound: wipe off the loose material with a dry cloth or paper towel.
  • Soak the remaining material with several drops of ArctiClean 1, wait 30 to 60 seconds, then wipe it off gently. Repeat if needed.
  • Always follow with ArctiClean 2: apply several drops, about as much as you used of ArctiClean 1, and wipe gently with a lint-free cloth until dry. Coffee filters make good, inexpensive lint-free cloths.

Technical data

Model ACN-60ml
ArctiClean 1 Thermal Material Remover, 30 ml, pale yellow liquid with a citrus (orange peel) odor, flash point 91°C (196°F)
ArctiClean 2 Thermal Surface Purifier, 30 ml, colorless liquid with a mild odor, pH 7.5
Compliance RoHS

Notes

  • ArctiClean 1 dissolves PS plastic and other plastics of the same family. Do not use it to clean these plastics.
  • Keep both bottles away from children and pets, and do not put them in your mouth.

In the box

  • 1x ArctiClean 1 Thermal Material Remover, 30 ml
  • 1x ArctiClean 2 Thermal Surface Purifier, 30 ml

Arctic Silver's instructions, ArctiClean 1 safety data sheet and ArctiClean 2 safety data sheet are all PDFs.

My Cart

You have no items in your shopping cart.